1. Metering of positive and negative active electric energy. The
electric energy shall be accumulated and stored
separately for tip, peak, flat, valley and other periods and the
total electric energy. It can store and display
various electric quantities in the last 12 months.
2. It can measure, store and display the current voltage, current,
power, power factor, frequency and other
operating parameters and status of the electric energy meter. It
has overload protection function.
3. There are two sets of rates (tip, peak, flat and valley) and
time periods that can be programmed at will, and
another set of rates and time periods can be used at the set time
point. At least 2 time zones can be set for
each set of rate periods throughout the year. At least 14 time
periods can be set within 24 hours; The minimum
interval between periods is 15 minutes. The time period can be set
across zero points.
4. It has such freezing functions as instantaneous freezing,
regular freezing, daily freezing, agreed freezing, and
hourly freezing.
5. It has the functions of event recording such as zero clearing,
programming, timing, power failure, switching on
and switching off.
6. Remote power off and transmission function: send power off
command through RS485 and other
communication interfaces to cut off the user's load circuit. Or
send the power transmission command to
connect the user load circuit.
7. Active upload/two-way transparent transmission function:
actively transmit data to the corresponding
platform through LoRaWAN/Cat. 1/Bluetooth (optional) wireless
network. The default interval is 4 hours
(settable).
- Specifications & technical parameters
Standards | IEC62053-21, IEC62052-11, DL/T645-2007 220 |
Voltage(V) | 220 |
Current(A) | 5(60)A/0.25～0.5(60)A |
Pulse constant(imp/kWh) | 3200 |
Active measurement accuracy | Class B/1 |
Reactive measurement accuracy | Class 2 |
Frequency | 50Hz |
Power consumption | ≤1.5W |
Specified range | 0.9Un ~ 1.1Un |
| Expansion range | 0.8Un ~ 1.15Un |
Limit range | 0.6Un ~ 1.2Un |
Specified temperature range | ≤±1s/d |
Reference temperature(23℃) | ≤±0.5s/d |
Active power(Class 1) | ≤0.004lb |
Reactive power(Class 2) | ≤0.005lb |
Specified working range | -25℃~+60℃ |
Operating limit range | -40℃~+70℃ |
Storage and transportation | -40℃~+70℃ |
Annual average relative humidity | < 75%RH |
Natural distribution within 30 days of a year | 95%RH |
Occurs occasionally in other days | 85%RH |
LoRaWAN frequency | CN470,RU864,IN865,EU868,US/AU915,KR920,AS923.1/2/3/4, Custom Channels |
The electric energy meter adopts LCD display. It can indicate the
cumulative total electricity consumption
and electricity consumption at various rates of the current and
last January to last December.
Status indicator lamp
The electricity meter uses a bright, long-life LED as a pulse
indicator light.
It has active power pulse indicator light: red, usually go out,
flashing when measuring active power.
LoRaWAN/Cat.1 Module status indicator: green. Always on indicates
online, and flashing indicates going online.
Among them, 5 and 6 are reactive pulse output (empty). 7 and 8 are
active pulse output. 9 and 10 are clocks. 11 and 12 are RS485.
Live installation of wiring is strictly prohibited!
The electricity meter shall be installed indoors as far as
possible. Special instrument box protection shall be used for
outdoor installation. The installation bottom plate shall be fixed
on the wall with strong fire resistance and not easy to vibration.
There must be no corrosive gases in the surrounding air where the
meter is installed. Avoid dust, salt spray, etc.
When using the electricity meter, the wiring must be conducted
strictly according to the wiring diagram in the tail cover of the
meter. It is recommended to use copper wire for the lead connected
to the terminal seat. The screws of the fixed lead in the terminal
seat should be tightened to avoid burning the electricity meter due
to bad contact and heating.
